基于单应性矩阵的模型迎角单目视频测量方法

风洞试验中模型迎角的精准测量是降低阻力系数误差的重要途径之一，为此，提出了基于单应性矩阵的模型迎角单目视频测量方法。该方法通过两个单应性矩阵，获取试验过程中相机实时位姿和标记点物方空间位置坐标，应用坐标旋转关系，完成试验模型的迎角测量。数值仿真试验结果表明：迎角测量误差与待测标记点到风洞壁板间的距离偏差近似为线性关系，因此，当标记点不满足共面条件时，可根据该特点进行测量误差修正。静态标定和风洞迎角测量试验结果表明：修正系统误差后，迎角实测数据的测量准度在0.01°以内，精度不超过0.012°。本文方法易于实施，工程实用价值强。     

基于LSTMAttention网络的短期风电功率预测

提出一种基于LSTMAttention网络的短期风电功率预测方法。首先,使用LSTM网络对数值天气预测(NWP)数据的特征信息进行提取,同时采用注意力机制有效分析了模型输入与输出的相关性,从而获取了更多重要时间的整体特征；其次,使用卷积神经网络(CNN)提取NWP数据的局部特征,并引入压缩和奖惩网络(SE)模块学习特征权重,利用特征重新标定方式提高网络表示能力；最后,将局部特征和整体特征进行特征融合,通过分类器输出分类结果。利用NOAA提供的美国加利福尼亚州某风电场的数据进行案例分析,证明了所提方法的有效性。试验结果表明,与BP神经网络、自回归积分滑动平均模型(ARIMA)模型和LSTM模型相比,LSTMAttention模型具有更高的预测精度,证明了该方法的有效性。     

高超声速圆锥边界层失稳条纹结构实验研究

边界层转捩的准确预测是高超声速飞行面临的关键气动问题之一。为研究高超声速边界层失稳和转捩机理,以前缘半径1.6mm、半锥角7°的圆锥模型为研究对象,在FD-07高超声速风洞中采用红外热图技术开展边界层转捩实验测量。通过与工程计算结果对比,确认模型表面边界层流态。实验结果表明:有迎角条件下,模型表面中后段出现条纹结构,条纹结构的起始位置随着周向角的增加而向上游移动;随着迎角的增加,条纹起始位置向上游移动,条纹强度差异和条纹与模型中心线的夹角越来越大。实验获得的条纹结构与不同频率扰动波相互作用直接数值模拟获得的条纹结构现象一致。通过对比分析,认为边界层内不同频率扰动波相互作用是产生条纹结构的一种机制。     

Statistical characteristics of low latitude Pc4s: Influence of solar wind and IMF parameters

Pc4 signatures for the year 2013, extracted from geomagnetic north–south and east–west components of induction coil magnetometer (LEMI 30) from low latitude station Desalpar (DSP), operated by Institute of Seismological Research (ISR), India have been investigated vis-à-vis the prevalent interplanetary parameters (IMF) as well as the geomagnetic activity indices. A clear dominance of Pc4-5 (467 events) over Pc3 (17 events) is observed. Local time variation of Pc4 shows a peak in the noon sector in both X and Y components. Our investigations show that the dominant peak frequency is 10 mHz at low latitude region. Correlations with solar wind and IMF parameters illustrate highest occurrence of Pc4 for a solar wind speed of 300–400 km/s and average IMF B field of 3–6 nT. The amplitude of Pc4s at DSP shows an increase with increasing solar wind speed, plasma density, solar wind dynamic pressure and average B field which is also reflected in the trend of frequency variation of these pulsations. We report that IMF clock angle at low latitude does not have influence on Pc4 occurrence. Based on the characteristics of these events, detected in latitudinally distributed stations from low and mid-latitudes from northern and southern hemisphere, we infer that modes were compressional, which could be driven by K-H instability or solar wind dynamic pressure, as compressional modes can propagate to low latitude with little attenuation.     

某飞行器推力矢量试验测力装置研制

为满足某飞行器推力矢量试验的测试要求,采用两台六分量应变天平和一个空气桥组成测力装置来实现飞机全机气动力和喷管推进特性同时分别测量。基于有限元软件,对天平的应变及空气桥对天平的干扰进行了分析。结果表明:空气桥对天平力分量的干扰值优于5%,对力矩(滚转力矩除外)分量的干扰值优于15%,达到了设计指标。通过校准获得了单独天平、天平带空气桥(充压、不充压)状态下的校准公式,校准结果表明:两台天平各分量的综合加载误差均优于0.3%,天平带空气桥(充压、不充压)状态下各分量的综合加载误差优于0.5%,空气桥对天平的干扰量值与有限元分析结果一致。理论分析与实测结果证明:研制的天平及空气桥达到了预定目标,它的测量精准度高,满足推力矢量风洞试验需求。     

Sunspot activity and cosmic ray modulation at 1 a.u. for 1900–2013

The descent of sunspot cycle 23 to an unprecedented minimum of long duration in 2006–2009 led to a prolonged galactic cosmic ray (GCR) recovery to the highest level observed in the instrumental era for a variety of energetic charged particle species on Earth, over a wide range of rigidities. The remarkable GCR increase measured by several ground-based, balloon-borne, and detectors on a satellite is described and discussed. It is accompanied by a decrease in solar wind velocity and interplanetary magnetic field at 1 a.u., reaching the lowest values since measurements of the solar wind began in October 1963; the solar polar field strength (μT) measured at the Wilcox Solar Observatory (WSO) is also significantly reduced compared to prior cycles since the start of the program in 1976, the polar field in the northern hemisphere reversed in June 2012 and again in February 2014, that in the southern hemisphere reversed in July 2013. If updates of WSO data confirm the second reversal in northern solar hemisphere, it would pose a serious challenge to the Dynamo Theory. The long-term change in solar behavior may have begun in 1992, perhaps earlier. The physical underpinnings of these solar changes need to be understood and their effect on GCR modulation processes clarified. The study discusses the recent phenomena in the context of GCR modulation since 1900. These happenings affected our empirical predictions for the key parameters for the next two sunspot cycles (they may be progressively less active than sunspot cycle 24) but it enhanced support for our prediction that solar activity is descending into a Dalton-like grand minimum in the middle of the twentyfirst century, reducing the frequency of the coronal mass ejections; they determine the space weather affecting the quality of life on Earth, radiation dose for hardware and human activities in space as well as the frequency of large Forbush decreases at 1 a.u.     

多飞行器再入段时间协同弹道规划方法

提出了一种多飞行器再入段时间协同弹道规划方法。首先,在纵向平面内规划满足航程与终端约束的纵向标称轨迹。随后,在采用轨迹跟踪律跟踪纵向标称轨迹的同时,运用考虑初始横侧向状态的多边界航向偏差角走廊策略控制飞行器的横侧向机动,以满足到达时间约束与终端约束,进而实现单枚飞行器到达时间约束下的轨迹规划。在此基础上,完成了飞行器的到达时间分布与飞行能力分析,给出了最小与最大到达时间的分析计算方法,并根据多飞行器协同再入的任务需求完成了协同飞行时间决策。最后,多飞行器协同再入与扰动条件下的仿真结果表明,该方法能够规划出满足到达时间与终端约束的协同再入轨迹,具备良好的计算精度与鲁棒性。     

有翼再入飞行器气动外形集成设计优化

气动外形设计是有翼再入飞行器（RV-W）的关键技术之一。分析了气动参数对再入飞行性能的影响,探讨了有翼再入飞行器气动外形设计的规律和准则。基于上述设计准则,以类X-37B飞行器为研究对象,集成几何参数化建模、气动力、气动热、热防护等学科快速分析方法,采用多学科设计优化方法,以最优气动特性为目标对飞行器气动外形进行了优化;得到优化气动外形后,对飞行器热防护系统（TPS）进行了轻量化设计优化。结果表明,优化外形的气动特性相比初始外形得到了较大的提升,设计优化得到的热防护系统重量占比（8.7%）优于同类飞行器的热防护系统重量占比统计数据,说明了本文有翼再入飞行器气动外形集成设计优化方法的有效性,可为同类飞行器提供参考。     

高超声速钝头体边界层转捩试验

为研究高超声钝头体边界层转捩以及头部钝度对转捩的影响,在FD-14和FD-14A两座激波风洞中开展了热流、压力扰动和高速纹影显示等综合测量。试验结果表明,转捩雷诺数关于钝度雷诺数的变化显示出转捩反转的趋势。压力扰动的功率谱密度（PSD）分析结果以流向离散分布云图形式显示,边界层高速纹影图像显示了第二模态波的发展、湍流的生成和熵层对边界层结构的显著影响。大头部钝度带来的强熵梯度熵层流动对边界层压力扰动频谱特性和流动结构影响显著,在转捩反转机理中起到重要作用。此外,马赫数对转捩的影响不容忽视。     

1 500℃极端高温环境下高超声速飞行器轻质隔热材料热/振联合试验

远程高超声速飞行器处于极为恶劣的气动加热与振动耦合环境中,长时间的高温与振动载荷相互叠加会导致飞行器热防护材料出现裂纹、错位、剥离或脱落,甚至会引发致命的安全事故。因此热防护材料在极端高温环境下的地面热/振联合试验测试,对于高超声速飞行器的安全可靠性设计极为重要。建立高温与振动复合试验环境,设法解决轻质多孔隔热材料在强振动下,表面温度难于准确测量与控制的难题,制作水冷式隔热装置保护价格昂贵的振动激励设备等,实现了1 500℃高温环境下高超声速飞行器轻质隔热材料的热/振联合试验。得到非金属隔热材料陶瓷纤维板内部的断裂形貌及裂纹断面特征。根据试验前、后材料的表观及微观变化以及内部结合剂的变化等试验结果,对材料进行改进。经过试验测试后,达到了使用要求。本文建立的1 500℃极端高温环境下的热/振联合试验系统及试验结果为远程高超声速飞行器热防护材料的抗振动能力评估、隔热效果确定以及材料性能的改进提供了重要支撑。